Abbott Precision XceedPro Návod k obsluze Strana 48
- Strana / 85
- Tabulka s obsahem
- ŘEŠENÍ PROBLÉMŮ
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
8-1
Questions? Refer to Page 10-10 for Technical Support Instructions.
Monitor Configuration
The Precision Xceed Pro Monitor configuration settings are enabled via the data management system. These settings
can be viewed on the hand-held device, but cannot be changed on it. Settings that are configured through the data
management system are:
Upload interval
Length of time between data uploads.•
Whether you can continue to test (“allow test” or “warn”) or not (“lockout”).•
Operator ID
Whether the Operator ID is required, optional or not used for all tests.•
Define the Operator ID prompt.•
The minimum and maximum number (between 1 and 30) of digits that are acceptable for the Operator ID. •
With manual entry of the Operator ID, determine whether a check digit is required (modulus 10 or 11).•
Decide acceptable formats for the Operator ID bar code. Refer to the Bar Code Specifications in Chapter 12 for •
available formats.
The monitor can truncate (ignore) the leading digits and/or the last digits of an Operator ID. The monitor can be set •
to select specific digits of an Operator ID. The number of digits is configured in the data management system
.
Patient Tests / Patient ID
Determine whether the Patient ID is required, optional or not used for patient tests.•
Define the Patient ID prompt.•
The minimum and maximum number (between 1 and 30) of digits that are acceptable for the Patient ID.•
Permission for manual entry of the Patient ID.•
Determine whether duplicate entry of a manually entered ID is required.•
With manual entry of the Patient ID, determine whether a check digit is required (modulus 10 or 11).•
Decide acceptable formats for the Patient ID bar code. Refer to the Bar Code Specifications in Chapter 12 for •
available formats.
The monitor can truncate (ignore) the leading digits and/or the last digits of a Patient ID. The monitor can be set to •
select specific digits of a Patient ID. The number of digits is configured in the data management system.
Decide whether confirmation of the Patient ID required.•
Determine how the ID will be confirmed.•
Decide whether comment code is required, optional or not used for patient tests that are in the acceptable range •
for the facility and the test strip.
Decide whether comment code is required, optional or not used for patient tests that are outside of the acceptable •
range for the facility and the test strip.
Control Tests
Set which levels of control solution are required, optional or not used by your facility. The monitor can be •
configured to run any combination of low, mid and high control solution tests.
Set whether control solution test results display as numeric or as Pass/Fail.•
Determine whether a comment code is required, optional or not used for control tests that are within the •
acceptable range for the facility and the test strip.
Decide whether a comment code required, optional or not used for control tests that are outside of the acceptable •
range for the facility and the test strip.
QC Interval
Determine how frequently QC tests need to be run. This can be set to a number of hours or up to three specified •
times during the day.
Decide whether the operator can continue to test (“allow test” or “warn”) or not (“lockout”) when the QC interval •
is expired.
Review Setup
Chapter 8: Review Setup
- Operator’s Manual 1
- Table of Contents 2
- 1. Overview 4
- Intended Use 5
- TrueMeasure 5
- TrueAccess 5
- Overview 5
- Icons and Warnings 6
- Conventions 6
- System Components 7
- Blood Glucose Test Strip 8
- Blood β-Ketone Test Strip 8
- Chapter 1: Overview 9
- 2. Using the Monitor 10
- Chapter 2: Using the Monitor 11
- Data Port 12
- Battery Compartment 12
- Port Protector 12
- Monitor Identification 13
- Menu Tree 13
- 3. Patient Test 14
- Patient Test 15
- Collecting Blood Samples 16
- Disposing of Waste 16
- Chapter 3: Patient Test 17
- 4. Control Test 22
- Control Test 23
- Chapter 4 : Control Test 24
- 5. Data Review 28
- Data Review 29
- Chapter 5: Data Review 30
- 105 mg/dL 31
- Data Review for Control Data 34
- 45 mg/dL 36
- 6. Proficiency Test 37
- Proficiency Test - Glucose 38
- Proficiency Test 38
- Chapter 6: Proficiency Test 39
- Proficiency Test - β-Ketone 41
- 7. Linearity Test 42
- Linearity Test 43
- Chapter 7: Linearity Test 44
- 8. Review Setup 47
- Monitor Configuration 48
- Review Setup 48
- Chapter 8: Review Setup 49
- Out-of-Range screen 55
- Test Setup menu 55
- System Status 58
- 9. Data Upload 60
- Data Upload 61
- Docking Station 62
- Mounting Instructions 62
- Enabling Data Upload 63
- 10. Troubleshooting 64
- Troubleshooting 65
- Error Messages 66
- Chapter 10: Troubleshooting 67
- When a Test is Selected: 69
- During Any Test: 70
- 20 mg/dL 72
- When Data Review is Selected: 73
- Returning an Instrument 74
- Contacting Abbott for Service 75
- LATIN AMERICA 76
- MIDDLE EAST AND AFRICA 76
- NORTH AMERICA 76
- 11. Maintenance 77
- Maintenance 78
- Battery Life 79
- Replacing the Batteries 79
- 12. Specifications 80
- Precision Xceed Pro Monitor 81
- Specifications 81
- Bar Code Types 83
- Important Safety Instructions 84
© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.031 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce